Volume 3, Issue 1, June 2019, Page: 18-23
Study on Tensile, Bending and Water Uptake Properties of Sugarcane Bagasse Fiber Reinforced Polypropylene Based Composite
Mohammad Bellal Hoque, Department of Textile Engineering, Fareast International University, Dhaka, Bangladesh; Institution of Radiation and Polymer Technology, Bangladesh Atomic Energy Commission, Dhaka, Bangladesh
Md. Sahadat Hossain, Glass Research Division, Bangladesh Council of Scientific and Industrial Research, Dhaka, Bangladesh
Ruhul A. Khan, Institution of Radiation and Polymer Technology, Bangladesh Atomic Energy Commission, Dhaka, Bangladesh
Received: Apr. 11, 2019;       Accepted: May 21, 2019;       Published: Jun. 13, 2019
DOI: 10.11648/j.jb.20190301.13      View  54      Downloads  10
Abstract
In this study, sugarcane bagasse fiber reinforced polypropylene based composites were fabricated successfully and their tensile, bending and water uptake behavior were studied. The composites were prepared by compression molding process. The fiber composition in the composites was 30% by weight. Results revealed that due to reinforcement by fiber, composites achieved 51% increase in tensile strength, 151% in tensile modulus, 109% in bending strength and 68% in bending modulus over that of polypropylene. Elongation at break was reduced due to the lower elongation property of fiber. The composites were treated by alkali for checking out the effects of alkali on composites. The concentrations of alkali used for treating the composites were 3%, 5% and 7% solution of sodium hydroxide (NaOH) and it was found that 7% solution of sodium hydroxide demonstrated lowest tensile and bending properties. Sheared composite samples were immersed into deionized water and it was noticed that composite samples were absorbed 2.10% water within 40 minutes of water absorption test. Soil degradation test was carried out for 16 weeks and it was observed that, the tensile and bending properties of sugarcane bagasse fiber reinforced polypropylene based composites were degraded slowly. The composites lost 35% of their original mechanical properties and retained 54% of actual weight after 16 weeks of degradation in soil medium.
Keywords
Sugarcane Bagasse Fiber, Polypropylene, Composite, Tensile Properties, Bending Properties
To cite this article
Mohammad Bellal Hoque, Md. Sahadat Hossain, Ruhul A. Khan, Study on Tensile, Bending and Water Uptake Properties of Sugarcane Bagasse Fiber Reinforced Polypropylene Based Composite, Journal of Biomaterials. Vol. 3, No. 1, 2019, pp. 18-23. doi: 10.11648/j.jb.20190301.13
Copyright
Copyright © 2019 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Reference
[1]
Mohammad Bellal Hoque, Solaiman, A. B. M. Hafizul Alam, Hasan Mahmud and Asiqun Nobi, Mechanical, Degradation and Water Uptake Properties of Fabric Reinforced Polypropylene Based Composites: Effect of Alkali on Composites, fibers 2018, 6, 94.
[2]
Mohammad Bellal Hoque, Md. Sahadat Hossain, Abdul M. Nahid, Solaiman Bari and Ruhul A. Khan, "Fabrication and Characterization of Pineapple Fibre-Reinforced Polypropylene Based Composites", Nano Hybrids and Composites 21 (2018) 31-42.
[3]
Arun M Panicker, Rose Maria, KA Rajesh and TO Varghese, Bit coir fiber and sugarcane bagasse fiber reinforced eco-friendly polypropylene composites: Development and property evaluation thereof, Journal of Thermoplastic Composite Materials (2019), doi: https://doi.org/10.1177/0892705718820403.
[4]
P. Vignesh, G. Venkatachalam A. Gautham Shankar, Anshuman Singh, Rish iPagaria, AnkitaPrasad, Studies on Tensile Strength of Sugarcane Fiber Reinforced Hybrid Polymer Matrix Composite, Materials Today: Proceedings, Volume 5, Issue 5, Part 2, 2018, Pages 13347-13357.
[5]
Anggono, J., Elvira Farkas, A., Bartos, A., Móczó, J., Antoni, Purwaningsih, H., Pukánszky, B., Deformation and failure of sugarcane bagasse reinforced PP, European Polymer Journal (2018), doi: https://doi.org/10.1016/j.eurpolymj.2018.12.033.
[6]
Mustaffa Zainal, Muhammad Zaid Aihsan, Wan Azani Mustafa, Ragunathan Santiagoo, Experimental Study on Thermal and Tensile Properties on Polypropylene Maleic Anhydride as a Compatibilizer in Polypropylene/Sugarcane Bagasse Composite, Journal of Advanced Research in Fluid Mechanics and Thermal Sciences, Volume 43, Issue 1 (2018) 141-148.
[7]
Lila MK, Singhal A, Banwait SS, Singh I, A recyclability study of bagasse fiber reinforced polypropylene composites, Polymer Degradation and Stability (2018), doi: 10.1016/j.polymdegradstab.2018.05.001.
[8]
Md. Sahadat Hossain, Muhammad B. Uddin, Md. Razzak, A. M. Sarwaruddin Chowdhury & Ruhul A. Khan, Fabrication and characterization of jute fabrics reinforced polypropylene-based composites: effects of ionizing radiation and disaccharide (sucrose), Radiation Effects and Defects in Solids 172: 11-12 (2017) 904-914.
[9]
Daniella R. Mulinari, Joyce de Paula Cipriano, Maria Rosa Capri & Amanda Torres Brandão (2017): Influence of Surgarcane Bagasse Fibers with Modified Surface on Polypropylene Composites, Journal of Natural Fibers, DOI: 10.1080/15440478.2016.1266294.
[10]
Li-Ping Wu, Wu-Li Kang, Yi Chen, Xin Zhang, Xiao-Hong Lin, Li-Ye Chen and Jing-Gang Gai, Structures and properties of low-shrinkage polypropylene composites, Journal of Applied Polymer Science 134 (2016) 44275.
[11]
Putinun Uawongsuwan, Yuqiu Yang and Hiroyuki Hamada, Long jute fibre-reinforced polypropylene composite: Effects of jute fibre bundle and glass fibre hybridization, Journal of Applied Polymer Science 132 (2014) 41819.
[12]
Deepak Varshney, Kishore Debnath and Inderdeep Singh, Mechanical Characterization of Polypropylene (PP) and Polyethylene (PE) Based Natural Fibre Reinforced Composites, International Journal of Surface Engineering & Materials Technology 4 (2014) 16-23.
[13]
Md Nuruzzaman Khan, Juganta K. Roy, Nousin Akter, Haydar U. Zaman, Tuhidul Islam and Ruhul A. Khan, Production and Properties of Short Jute and Short E-Glass Fibre Reinforced Polypropylene-Based Composites, Open Journal of Composite Materials 2 (2012) 40-47.
[14]
Shamsun Nahar, Ruhul A. Khan, Kamol Dey, Bapi Sarker, Anjan K. Das and Sushanta Ghoshal, Comparative Studies of Mechanical and Interfacial Properties between Jute and Bamboo Fibre-Reinforced Polypropylene-Based Composites, Journal of THERMOPLASTIC COMPOSITE MATERIALS 25 (2012) 15-32.
[15]
Md. Sahadat Hossain, A. M. Sarwaruddin Chowdhury & Ruhul A. Khan, Effect of disaccharide, gamma radiation and temperature on the physico-mechanical properties of jute fabrics reinforced unsaturated polyester resin-based composite, Radiation Effects and Defects in Solids 172: 5-6 (2017) 517-530.
[16]
Nangia, S. and Biswas, S., “Jute Composite: Technology & Business Opportunities”, In: Proceedings of International Conference on Advances in Composites, Banglore, India, 24-26 August (2000) pp. 295-305.
[17]
Kalaprasad G., Pradeep P., Mathew G., Pavithran C. and Thomas S., “Thermal Conductivity Analyses of Low Density Polyethylene Composites Reinforced with Sisal”, Glass and Intimately Mixed Sisal Glass Fibres, Composites Science and Technology 60 (2000) 2967-2977.
[18]
Andrade MF and Colodette JL., Dissolving pulp production from sugarcane bagasse. Industrial Crops and Products 52 (2014) 58-64.
[19]
E. F. Cerqueiraa, C. A. R. P. Baptistab, D. R. Mulinaria, Mechanical behaviour of polypropylene reinforced sugarcane bagasse fibers composites, Procedia Engineering 10 (2011) 2046–2051.
[20]
Pandey A, Soccol CR, Nigan P, Soccol VT, Vanderberghe LP and Mohan R., Biotechnology potential of agro industrial residues. i: sugarcane bagasse. Bioresource Technology 74 (1) (2000) 69-80.
[21]
Soccol CR and Vandenberghe LP, Overview of applied solid-state fermentation in Brazil, Biochemical Engineering Journal 3 (2-3) (2003) 205-218.
[22]
Khan R. A., Khan M. A., Sultana S. and Noor F. G, “Mechanical, Degradation, and Interfacial Properties of Synthetic Degradable Fibre Reinforced Polypropylene Composites”, Journal of Reinforced Plastics and Composite 29 (2009) 466–476.
[23]
Garcia, M., Vliet, G. V., Jain, S., Zyl, W. E. V. and Boukamp, B., “Polypropylene/SiO2 Nano Composites with Improved Mechanical Properties”, Reviews on Advanced Materials Science 6 (2004) 169–175.
[24]
Karmaker, A. C. and Hinrichsen, G., “Processing and Characterization of Jute Fibre Reinforced Thermoplastic Polymers”, Polymer – Plastics Technology and Engineering 30 (1999) 609–621.
[25]
Khan M. A., Hinrichsen G. and Drzal, L. T., “Influence of Noble Coupling Agents on Mechanical Properties of Jute Reinforced Polypropylene Composites”, Journal of Materials Science Letters 20 (2001) 1211–1713.
[26]
Bledzki, A. K. and Gassan, J., “Composites Reinforced with Cellulose Based Fibres”, Journal of Progress in Polymer Science 24 (1999) 221–274.
[27]
Wambua P., Ivan J. and Verport, I., 2, “Natural Fibres: Can They Replace Glass in Fibre Reinforced Plastics”, Journal of Composites Science and Technology 63 (2003) 1259–1264.
[28]
Czvikovszky T., “Reactive Recycling of Multiphase Polymer Systems”, Nuclear Instruments and Methods in Physics Research B. 105 (1995) 233–237.
Browse journals by subject